dpm-addpool man page

DPM-ADDPOOL(1) DPM Administrator Commands DPM-ADDPOOL(1)

[1mNAME[0m
dpm-addpool - define a new disk pool

[1mSYNOPSIS[0m
[1mdpm-addpool --poolname [4m[22mpool_name[24m [1m--def_filesize [4m[22mdefsize[24m [ [1m--def_life-[0m
[1mtime [4m[22mdef_lifetime[24m ] [ [1m--def_pintime [4m[22mdefpintime[24m ] [ [1m--gc_start_thresh[0m
[4mperc[24m ] [ [1m--gc_stop_thresh [4m[22mperc[24m ] [ [1m--gid [4m[22mpool_gids[24m ] [ [1m--group[0m
[4mpool_groups[24m ] [ [1m--help [22m] [ [1m--max_lifetime [4m[22mmax_lifetime[24m ] [ [1m--max_pin-[0m
[1mtime [4m[22mmaxpintime[24m ] [ [1m--ret_policy [4m[22mretention_policy[24m ] [ [1m--s_type[0m
[4mspace_type[24m ]

[1mDESCRIPTION[0m
[1mdpm-addpool [22mdefines a new disk pool.

This command requires ADMIN privilege.

[1mOPTIONS[0m
[4mpool_name[0m
specifies the disk pool name. It must be at most CA_MAXPOOL-
NAMELEN characters long.

[4mdefsize[0m
specifies the default amount of space reserved for a file. This
is by default in bytes, but the number may also be post-fixed
with 'k', 'M' or 'G' for kilobyte, Megabyte and Gigabyte respec-
tively.

[4mdef_lifetime[0m
specifies the default time a space or volatile file is kept in
the system (in seconds).

[4mdefpintime[0m
specifies the default time a file is kept on a given disk (in
seconds).

[4mgc_start_thresh[0m
specifies the minimum free space in the pool. If the percentage
of free space goes below this value, the garbage collector is
started. Default is 0.

[4mgc_stop_thresh[0m
specifies the percentage of free space in the pool above which
the garbage collector is stopped. Default is 0.

[4mmax_lifetime[0m
specifies the maximum time a space or volatile file is kept in
the system (in seconds).

[4mmaxpintime[0m
specifies the maximum time a file is kept on a given disk (in
seconds).

[4mpool_gids[0m
if not zero, the disk pool is restricted to this comma separated
list of group gids.

[4mpool_groups[0m
if set and not "ALL", the disk pool is restricted to this comma
separated list of group names.

[4mretention_policy[0m
specifies the retention policy supported by the disk pool. It
can be [1mR [22m(for Replica), [1mO [22m(for Output) or [1mC [22m(for Custodial).
Default is [1mR[22m.

[4mspace_type[0m
indicates the type of space supported in the disk pool. It can
be [1mV [22m(for Volatile), [1mD [22m(for Durable), [1mP [22m(for Permanent) or [1m- [22m(to
accept any type). The latter is the default.

[1mEXAMPLE[0m
dpm-addpool --poolname Volatile --def_filesize 200M --s_type V

[1mEXIT STATUS[0m
This program returns 0 if the operation was successful or >0 if the
operation failed.

[1mSEE ALSO[0m
[1mdpm(1)[22m, [1mdpm_addpool(3)[0m

LCG $Date: 2010-02-05 10:50:58 +0100 (Fri, 05 Feb 2010)D$PM-ADDPOOL(1)

Info